How To Reset Maytag Dishwasher

(Many of the links in this article redirect to a specific reviewed product. Your purchase of these products through affiliate links helps to generate commission for Storables.com, at no extra cost. Learn more)

Introduction

Welcome to our guide on how to reset your Maytag dishwasher. If you’re experiencing any issues with your dishwasher, such as it not starting, not completing a cycle, or displaying error codes, performing a reset can often resolve these problems. Resetting the dishwasher essentially reboots its internal systems, allowing it to start fresh and potentially clear any temporary glitches or malfunctions.

Before we begin, it’s important to note that the reset process may vary slightly depending on the model of your Maytag dishwasher. However, the general steps we outline here should apply to most Maytag dishwasher models. Additionally, always refer to your specific dishwasher’s user manual for any model-specific instructions or troubleshooting tips.

Now, let’s dive into the step-by-step process of resetting your Maytag dishwasher.

Step 1: Turn off the Power

The first step in resetting your Maytag dishwasher is to ensure that the power is completely turned off. This is an important safety measure to prevent any accidental electrical shocks or malfunctions during the reset process.

To turn off the power, locate the dishwasher’s power cord. It is usually located at the back of the dishwasher, near the bottom. Unplug the power cord from the electrical outlet or, if your dishwasher is hardwired, turn off the circuit breaker that supplies power to the dishwasher.

Double-check that the dishwasher is completely disconnected from any power source before proceeding to the next step.

Once you have ensured that the power is turned off, you are ready to move on to the next step in the reset process.

Step 2: Open the Dishwasher Door

Now that the power is turned off, it’s time to open the dishwasher door. This step is necessary to access the control panel and buttons that we’ll be using for the reset process.

Gently grasp the handle of the dishwasher door and pull it open. Take care not to force or slam the door, as it may cause damage to the hinges or the door itself.

Once the dishwasher door is fully open, you will have clear visibility and access to the control panel located on the front of the dishwasher. This is where we will navigate through the reset process.

Keep the dishwasher door open for the duration of the reset process, as we will need access to the control panel in the following steps.

With the dishwasher door open and ready, we can now proceed to the next step in resetting your Maytag dishwasher.

Step 3: Press and Hold the “Heated Dry” Button

With the dishwasher door open, locate the control panel on the front of the dishwasher. Look for the “Heated Dry” button, which is typically labeled and may have a corresponding icon indicating heat or drying.

Press and hold down the “Heated Dry” button firmly for about 3-5 seconds. This action initiates the reset process and prepares the dishwasher for the next step.

While pressing the “Heated Dry” button, you may notice some indicators or lights on the control panel flashing or changing. This is normal and indicates that the dishwasher has entered reset mode.

Continue to hold down the “Heated Dry” button until you are ready to proceed to the next step.

Once you have held down the “Heated Dry” button for the appropriate duration, you can release it and move on to the next step in the reset process.

Step 4: Press the “Normal” Button

After releasing the “Heated Dry” button, your next step in resetting the Maytag dishwasher is to locate and press the “Normal” button on the control panel. This button is typically labeled and may have a corresponding icon indicating a regular or standard cycle.

Press the “Normal” button firmly. This action tells the dishwasher to enter the normal cycle mode, which is necessary for the reset process.

As you press the “Normal” button, you may notice additional indicators or lights on the control panel flashing or changing. This is a normal part of the reset process.

Keep the “Normal” button pressed for a few seconds to ensure the dishwasher registers the command properly.

Once you have pressed the “Normal” button, you can move on to the next step in resetting your Maytag dishwasher.

To reset a Maytag dishwasher, locate the circuit breaker or unplug the dishwasher for a few minutes, then plug it back in or flip the circuit breaker back on to reset the system.

Step 5: Release the “Heated Dry” Button

Now that you have pressed the “Normal” button, it’s time to release the “Heated Dry” button that you were holding down in the previous step.

Gently release your finger from the “Heated Dry” button. You may notice that the control panel indicators on the dishwasher may change or stop flashing as you release the button. This is normal and indicates that the dishwasher has registered the button commands.

Ensure that you fully release the “Heated Dry” button and do not press it again during the reset process.

By releasing the “Heated Dry” button, you have successfully completed the necessary actions for this step. Now, let’s move on to the next step in resetting your Maytag dishwasher.

Step 6: Press the “Start/Resume” Button

With the previous steps completed, it’s time to progress to the next button in the reset process: the “Start/Resume” button.

Locate the “Start/Resume” button on the control panel of your Maytag dishwasher. This button is typically labeled and may have a corresponding icon indicating a play or start symbol.

Press the “Start/Resume” button firmly to initiate the reset sequence. This tells the dishwasher to begin the reset process and clear any residual data or settings.

As you press the “Start/Resume” button, you may notice the control panel indicators or lights flashing or changing again. This is an indication that the dishwasher has received the reset command and is entering the reset mode.

Hold down the “Start/Resume” button for a few seconds to ensure that the dishwasher fully registers the command.

After pressing the “Start/Resume” button, you can proceed to the next step in resetting your Maytag dishwasher.

Step 7: Close the Dishwasher Door

Now that you have completed the necessary actions on the control panel, it’s time to close the dishwasher door. This step ensures proper sealing and allows the dishwasher to commence the reset process.

Gently push the dishwasher door until it is securely closed. Ensure that the door is fully latched and there are no obstructions that may prevent it from closing properly.

Closing the dishwasher door activates the internal systems and allows the reset to take place. It also prevents any water or steam from leaking out during the reset process.

Once the dishwasher door is closed, you are ready to move on to the next step in resetting your Maytag dishwasher.

Step 8: Wait for the Reset to Complete

After closing the dishwasher door, the final step in resetting your Maytag dishwasher is to patiently wait for the reset process to complete. This may take a few minutes.

During the reset process, the dishwasher’s internal systems will go through a series of checks and adjustments to ensure that everything is functioning properly. This includes clearing any error codes, resetting settings, and calibrating the dishwasher’s sensors.

While the reset is in progress, it’s important to avoid interrupting the process by not opening the dishwasher door or tampering with any buttons or controls. Let the dishwasher complete the reset on its own.

As you wait, you may notice the control panel indicators or lights turning on and off or changing. This is a normal part of the reset process and indicates that the dishwasher is actively resetting and recalibrating.

Once the reset is complete, the dishwasher’s indicators or lights should stabilize and return to their normal state.

When the reset process has finished and the dishwasher is ready, you will be able to use it as usual. At this point, you can open the dishwasher door, select a cycle, and start a new cleaning cycle.

Remember to refer to your Maytag dishwasher’s user manual for any additional troubleshooting tips or specific instructions related to resetting your particular model.

Congratulations! You have successfully completed the reset process for your Maytag dishwasher. If you were experiencing any issues before, they should now be resolved.

Note: If the reset process does not resolve the issue with your Maytag dishwasher, it’s recommended to contact Maytag customer support or a professional technician for further assistance.

Conclusion

Resetting your Maytag dishwasher can be a simple and effective solution to resolve various issues you may encounter, such as the dishwasher not starting, not completing a cycle, or displaying error codes. By following the steps outlined in this guide, you can easily reset your Maytag dishwasher and potentially restore its functionality.

Remember, while the steps provided are general guidelines, it is important to consult your specific Maytag dishwasher’s user manual for any model-specific instructions or troubleshooting tips. Additionally, if the reset process does not resolve the issue, it’s advisable to contact Maytag customer support or a professional technician for further assistance.

We hope this guide has been helpful in assisting you with resetting your Maytag dishwasher. By following these steps, you can efficiently reset your dishwasher and enjoy its reliable performance once again.

Thank you for choosing Maytag, and happy dishwashing!