DIY Guide To Installing A Kitchen Sink With Touchless Faucet And Soap Dispenser

(Many of the links in this article redirect to a specific reviewed product. Your purchase of these products through affiliate links helps to generate commission for Storables.com, at no extra cost. Learn more)

Installing a kitchen sink with a touchless faucet and a built-in soap dispenser can be a fantastic way to enhance both the functionality and aesthetic appeal of your kitchen. This DIY guide will walk you through the step-by-step process of installing these modern and convenient features, ensuring that your kitchen becomes more efficient and hygienic.

Preparation Before Installation

Before you start the installation process, it's crucial to prepare your tools and materials. Here’s a list of what you'll need:

• Touchless Kitchen Faucet: This includes the faucet body, mounting plate, gasket, and control box.
• Soap Dispenser: This typically includes the dispenser bottle, mounting nut, and rubber washer.
• Tools:
  • Basin wrench
  • Screwdriver
  • Cordless drill
  • Drill bits (for drilling holes)
  • Socket wrench
  • Mounting screws
  • Wall plugs
  • Electrical tape (if needed)
  • Adjustable wrench

Step 1: Shut Off Water Supply

The first and most critical step is to shut off the water supply to your kitchen sink. Locate the hot and cold-water shutoff valves underneath the sink and turn them clockwise to shut off the water supply. This will prevent any accidental water flow during the installation process.

Step 2: Disconnect Water-Supply Lines

Use a basin wrench to disconnect both water-supply lines from the underside of the sink. This is usually done by loosening the nuts that hold the supply lines in place. Once disconnected, place a bucket under the lines to catch any remaining water.

Step 3: Remove Old Faucet

Twist off the hand sprayer from the spray hose, then pry off the retainer clip with a narrow screwdriver or pocketknife. Pull the sprayer base off of the spray hose and push it down through the sink deck and into the cabinet below. Drain any remaining water from this hose into your bucket.

Next, pull out and discard the old faucet. This will give you clear access to install your new touchless faucet.

Step 4: Mount New Faucet

Place the new faucet’s mounting plate and gasket onto the sink deck. Set the faucet in place by feeding its hoses and data cable down through the hole in the mounting plate. From below, slide the ends of these hoses and cable through the support bar and mounting washer.

Thread on the hex nut and tighten it with your supplied wrench to lock the faucet to the sink. Make sure everything is securely fastened before moving on to the next step.

Step 5: Install Soap Dispenser

If your sink already has an extra hole for a soap dispenser, you can proceed directly to installing it. However, if there is no hole, you will need to drill one around your sink area. Use a drill bit that matches your dispenser's mounting requirements.

Check the design of your dispenser and follow its assembly instructions. Most dispensers come with a base fixed to the pump which can be easily removed to fill the tank or reservoir. Place this reservoir under your sink area using a mounting nut or gasket provided with your dispenser kit.

Thread this nut into place while ensuring it's securely fastened with rubber washers for better sealing. Place the bottle on top of this hole in your sink deck.

Step 6: Connect Wires and Tubes

For touchless faucets, you'll need to connect various wires and tubes according to your specific installation diagram provided with each product. This typically involves connecting sensor wires, adapter wires, liquid tubes, and power lines from both the faucet body and control unit.

For example:

• Connect faucet water hoses with control box outlets.
• Fix water hoses to control box inlets and triangular valves.
• Secure control boxes to holders using screws.
• Connect sensor wires as per instructions.

Step 7: Install Control Box

Take out of the battery box from control box and install four pieces of AA alkaline batteries correctly. Insert back into control box ensuring all connections are secure before proceeding further.

If required by your specific model, insert transformer plug into socket provided (if applicable). Ensure all electrical connections are waterproofed using electrical tape if necessary.

Step 8: Adjust Settings

Once all connections are made, adjust water-temperature settings according to preference using controls available on most modern touchless faucets.

Snap counterbalance weight onto hose connected to retractable spray head ensuring smooth operation without any leaks or issues during use.

Step 9: Test Installation

Open shutoff valves under sink allowing water supply back on while testing newly installed touchless faucet along with integrated soap dispenser ensuring both functions work seamlessly without any hiccups or leaks throughout entire process.

Additional Tips

1. Viscous Soap Avoidance: When filling hand soap into dispenser bottle, avoid using viscous soaps as they can lead to clogging issues affecting proper dispensing functionality over time.
2. Regular Maintenance: Regularly check both faucet body and soap dispenser for any signs of damage or clogging ensuring optimal performance at all times.
3. Matching Styles: Ensure both touchless faucet and integrated soap dispenser match in style and finish complementing overall aesthetic appeal enhancing overall kitchen ambiance significantly.

Conclusion

Installing a kitchen sink with touchless faucet along with built-in soap dispenser not only enhances convenience but also adds a touch of modernity making your kitchen look more organized while being highly functional too By following these detailed steps outlined above carefully ensuring each step is completed accurately without any errors will result in successful installation process yielding desired results immediately upon completion!

Remember always refer technical parameters provided by manufacturers specific requirements ensuring compatibility between different components used during installation process ensuring long-lasting durability without any issues arising later down line