Home>Full Guide To Have The Best DIY Garage Shelves>DIY Wood Garage Shelves: How To Build One

DIY Wood Garage Shelves: How To Build One

Full Guide To Have The Best DIY Garage Shelves • May 27, 2020

DIY Wood Garage Shelves: How To Build One

Written by: Kevin Ashwe

Never worry about having enough garage space again! These DIY wood garage shelves ideas are quick, easy and great for everyone.

It is easy to get the garage stuffed up, and make working or walking difficult due to lack of adequate space. There are some steps you can take if you want to get more space to work or store things in your garage. One of these workable steps is the installation of DIY wood garage shelves. Installing a DIY wood garage is not as difficult as you may think, plus it’s not costly. With some durable woods, planks, and some carpenter tools, you are good to go. You will get some perfect DIY wood storage shelves ideas on this list. For more home inspiration ideas, explore our comprehensive list of storage ideas.

 

 

DIY Wood Garage Shelves How To Build One - INFOGRAPHICS

 

 

This DIY shelf will save you a lot of space in your garage. One of the smartest ways to get sufficient space is to take advantage of the ceiling. Looking at it from another angle, it will protect your things better and offer easy access to them.

 

Working within space restrictions means that you have to make your existing space work for you. When considering storage shelves, it is important to always sit down and make a plan. This overhead garage shelf certainly makes use of some prime shelving real estate that might otherwise have gone to waste. 

 

Instructions

  1. Locate the ceiling joists.
  2. Measure how far you want the shelve hanged from the ceiling.
  3. You may use 4×8 sheets of plywood to create your bottom support, and use 3” screws to attach them to the downward supports.
  4. Add your plywood base with 1¼ -inch general purpose screws; to fasten them to the bottom.
  5. Arrange your garage goods.

 

Tips

  • This shelf can hold up to 200lbs. But you may try out yours with more substantial things if you install it well.
  • For this project, you must have plywood, stud finder, screws, circular saw, and cleats.
  • This shelf should only take a few hours to build. It depends on your expertise and the size of the shelves you want to construct.

 

 

It’s a concealed hanging shelf because you will have to mount it above your garage door. From outside, if the door is opened, the garage shelving will be invisible. Notably, this shelving idea can carry some stuff, but you are not advised to store heavy goods on it.

 

 

Instructions

  1. Prepare your tools and supplies: four 2x4x8-inches, about six lag screws and sized washers, two 2×4-inches sheets of plywood (pre-cut), 3-inch drywall screws, 1-inch deck screws, pencil or painters tape, saw to cut 2×4-inch lumber at a straight angle, screwdriver or power drill, measuring tape, level, and a stud finder.
  2. Locate studs, nark, and drill holes: consider the door when you are determining the above’s head clearance. And leave one inch after locating the measurement.
  3. Assemble shelf frames: to create a long and thin rectangular frame; cut just one of the 2×4 into two and attach two 8-inch with them. Then fasten this into the ceiling.
  4. Place the flat plywood: your 2×4-inch sheets of plywood should be screwed on the frames on each corner. Just ensure they are not shifting.
  5. Enjoy your new storage.

 

Tip

  • You can change the measurements of woods to suit your taste.

 

 

If you still have some space in your garage that can contain a standing shelf, you may want to construct this easy and simple shelf. Spending a few dollars on this DIY shelf will offer you sufficient space and a sturdy shelf to organize your valuable goods. You can get this done in less than 1 hour.

 

 

Instructions

  1. Prepare your tools and supplies.
  2. Cut your 98”x48” OSB into three 98”x16”.
  3. Cut the studs into six 8 feet long, four 5 feet long, two 13”. With these, you need six 13″, and four vertical legs.
  4. Assemble the sides in rectangular shapes; the three bottom sides should be 4″ from the bottom and nail the vertical sides. The third 4” should be in the middle.
  5. Screw or nail the lengths. You can use 3.5” nails. Use the nails on the 13” sides and the vertical side. Do this for all the 6 lengths.
  6. Assemble the OSB or plywood shelves with screws. If the boards are tight, use the hammer to bang them into the frames.
  7. Level the shelving legs and secure them if necessary.
  8. Gather your goods and store them.

 

Tip

  • Cut and construct the base frame. Take note that it’s a must to assemble the
    frame with the OSB or plywood correctly. To achieve this, you can use a hammer and screws to join them. Or else, you won’t be able to store heavy things on the shelf.

 

 

 

 

This garage shelving idea is very straightforward and fast to construct. You can make three to four shelves out of this idea, it all depends on what you want. You will need framing angles, a miter saw, joist hangers, an oriented strand board, and a power drill to complete the project.

 

 

Instructions

  1. Get all supplies.
  2. Mark the walls with consideration of the 2×4 wood thickness.
  3. Use a square and level to rule the line towards the adjacent wall.
  4. Pre-drill each hole for the 2×4’s and line them on the marked places on the wall.
  5. Make each of the shelves with OSB pieces of 8 feet x 20″
  6. Hang the shelves on the wall support the loose end with a 2 by 4-inch forming the pillar for the complete shelf.
  7. Plum all pillars and screw them. You can do more by adding joist hangers on the opposite end of the pillar sides. Doing that will eliminate the splitting of the wood.
  8. Trim the boards on all edges to level up with the loose end of shelves.
  9. Arrange your stuff and enjoy.

 

Tips

  • If you are a beginner, this is the right DIY garage shelf you should try.
  • In less than 2 hours, your stuff should be on it already.

 

 

You can never go wrong with floating shelf ideas. It’s the most common and straightforward DIY garage shelf you can try. In other words, this shelf is not expensive to construct. Floating shelves are the right way to clear the garage ground and have much space to do other things. As mentioned, when thinking about storage shelves, it is important to always consider the space you’re working within and be careful not to ignore overhead or wall space! 

 

 

Instructions

  1. Get all necessary materials and tools; 2x4x8” sheets (7/16” OSB), 9×8” long (2x4s), 4-inch deck screws, 12 angle brackets, 1 ½” screws, 4×6 length 6×1/2” Cedar Fence (optional).
  2. Rip OBS into 2x24inch, 18inch wide and 24inch wide.
  3. Build the ledger.
  4. Build the shear plates.
  5. Fix the shelving.
  6. Add the cedar fence all through the front of the shelf.
  7. Store your treasures on your new garage shelf.

 

Tip

  • This DIY garage shelf wouldn’t take you up to 2 hours to construct.

 

 

 

 

Some people are so good at storing old things that they can dig out an old item of about 20 years. If you are one of these people or you have lots of infrequently used items that you want to build a home for, this should be your savior.

 

 

Instructions

  1. Reclaimed lumber.
  2. Scrape boards.
  3. Locate the preferred corner.
  4. Rip shelf supports; you can rip three of 2×11” boards to have 2×3” boards for shelf supports.
  5. Find the studs and mount the support boards.
  6. If you are using 10” wide for shelf decking, rip them into half.
  7. Put additional top-shelf support.
  8. Install the face board.
  9. Add the finishing touch and enjoy.

 

Tip

  • To make a better room for them, you will need reclaimed lumber to achieve unique work and reduce expenses. Locate a perfect corner in your garage.

 

 

 

 

 

In case you prefer a remodeling shelf, or there is no vacant space on the wall again, you should try this design. It offers adequate space goods. In fact, you will organize your garage better with many sections on this shelf.

 

 

Instructions

  1. Gather tools and materials, 2x4x12” beams, 2x4x7” vertical supports, 2x4x10” frame pieces, 4x8x3/8 full sheet plywood, 2×4” piece, 3” nails or drywall screws, 1 ¼ drywalls screws, drill, pencil, hand saw, and speed square.
  2. Mark the dimensions on the wall.
  3. Layout the supports.
  4. Cut frame pieces.
  5. Assemble the frames and fasten them with screws into the wall and do the final assembly of the shelf. Three long sheets are okay for three shelves.
  6. Fasten the four vertical legs on the shelf edge.

 

 

If you want something huge and powerful to carry your bulky goods, head straight to the store to get materials for this. Provided you mount this well and use durable materials, you will have a heavy-duty shelf.

 

 

Instructions

  1. You will use 2x4s, wooden dowels, and particle boards, saw, clamps, cordless drill.
  2. Rip the 2×4 in halves, or you should buy the pre-cut particle boards.
  3. Connect all beams and posts with the wooden drill.
  4. Drill holes in the beams.
  5. Now drill holes in the posts.
  6. Glue them together; you can use ludicrous speed.
  7. Now make your boards. Mark all sizes of the posts on the four corners and then notch them out with a jigsaw.
  8. Sandpaper, paint, and work on the aesthetics as you desire.

 

Tip

  • To make your project fast, use tools that are in good condition (i.e., don’t use blunt saw).

 

 

 

 

Another weighty DIY garage shelf idea is this stud walls design. If you get compelling woods and install it properly, this shelf should last for many years.

 

 

Instructions

  1. Screw 2×4” to wall studs on your marked measurements. But make sure the height is perfect for tote storage.
  2. Tack screw the second 2×4” of the same size with first on the first one.
  3. Fasten legs at the appropriate places.
  4. Untack the second layer of 2×4” together with the legs.
  5. Add some cross supports and add the outer leg again.
  6. Place plywood shelving on the top.
  7. Arrange your garage stuff.

 

Tip

  • This method can be used to customize storage for strollers and bicycles.

 

 

Here is the most massive DIY garage shelving idea on this list. With this shelf, you can never lack space again. Plus, it features different sections for different sizes of goods. The shelf is 8 feet in height and 8 feet in width. You can also use 2×4″ woods, 18″ shelf support so that you won’t have much wood to cut off. You will need to get wood glue, plywood, and deck screws to complete the project. For aesthetics, you can make a vintage painting or anyone you like. You don’t need the whole day to complete this vast garage shelf.

 

 

Instructions

  1. Build five rectangle shape ladders.
  2. Make them look like a shelf by adding 4 legs on each corner and 2 legs across the middle on both sides.
  3. Screw the 2×4″ pegboards on the first, second, and third shelf. Leave out the fourth since it’s close to the ceiling, and nothing can be stored there.
  4. Arrange your things and give your garage a look it deserves.

 

Tips

  • You can cut a 4×4 pegboard into halves to get the fitting shelf boards.
  • This shelf is capable of holding heavy goods.

 

 

Suspended garage storage shelf for your garage will help you arrange and see your garage in a better condition. You should try this if indeed you want more space to arrange the cluttered stuff. You can make the shelf depth about 2-3 feet, and 8” long, depending on your choice.

 

 

Instructions

  1. Materials needed are four 2x4x8-inch studs, half sheet of ½-inch plywood or OSB, two Simpson strong tie (RTR connectors), four Simpson strong (workbench hardware kit), 2 1/2-inch string drive, 1 ¼-inch brad nails, and Simpson strong (8×1 ¼-inch screws-tie wafer head).
  2. Woodcutting list; one 2x4x96”, one 2x4x92”, two 2x4x22 1/2-inch, three 2x4x21”, two 2x4x35”. You may change the measurement depending on your garage clearance. Lastly, optional two 2x4x6”.
  3. Determine the distance from the height of the garage door to the ceiling.
  4. Arrange and assemble the shelf and frames.
  5. Mount the supports on the ceiling beam.
  6. Lift the shelf frame into the right.
  7. Cut the 4×8” sheet of plywood into equal halves long. cut the corner notches for vertical supports.
  8. Position the shelf frame on the top of the supports and screw or nail with 1 ¼-inch.
  9. Your garage shelf is ready.

 

Tip

  • If you notice that your plywood needs more support, then add a 2×4-inch block on the inside of all side pieces.

 

 

Having a neat and well-organized garage could be what you owe your home garage this year. Pick any one of the impressive DIY garage shelves on this list and tell your garage you are the boss.

Related Post