How To Change Water Filter In Lg Refrigerator

(Many of the links in this article redirect to a specific reviewed product. Your purchase of these products through affiliate links helps to generate commission for Storables.com, at no extra cost. Learn more)

Introduction

Having clean and filtered water is essential for maintaining a healthy lifestyle. One way to ensure that the water in your LG refrigerator is always clean and free from impurities is by regularly changing the water filter.

The water filter in your LG refrigerator is responsible for removing contaminants such as chlorine, sediment, and other impurities that can affect the taste and quality of your drinking water and ice. Over time, the filter becomes less effective and needs to be replaced.

Changing the water filter in your LG refrigerator is a simple process that can be done by following a few easy steps. In this article, we will guide you through the process, helping you maintain a continuous supply of clean and fresh-tasting water in your home.

Step 1: Locate the water filter

The first step in changing the water filter in your LG refrigerator is to locate its position. The location of the water filter may vary slightly depending on the model of your refrigerator. However, in most LG refrigerators, you can find the water filter either inside the refrigerator compartment or at the bottom of the refrigerator.

If the water filter is located inside the refrigerator compartment, you can typically find it either on the upper right-hand corner or the upper left-hand corner. Look for a small compartment or a cylindrical housing with a knob or button.

If the water filter is located at the bottom of your refrigerator, you might need to access it from the front by removing the kickplate or grille. Once you remove the kickplate or grille, you will find the water filter housing.

If you are unsure about the exact location of the water filter in your LG refrigerator, it is recommended to consult the refrigerator’s user manual or visit the LG website for specific instructions and diagrams.

Once you have located the water filter, make note of its size and type. LG refrigerators typically use either a push or twist-in water filter. This information will be helpful when purchasing a replacement water filter.

Step 2: Turn off the water supply

Before you can proceed with replacing the water filter in your LG refrigerator, it is essential to turn off the water supply. This step is crucial to prevent any water leakage or flooding during the filter replacement process.

To turn off the water supply, you first need to locate the water shut-off valve. The shut-off valve is typically located behind the refrigerator or under the sink. It may be connected to a water line or pipe that supplies water to your refrigerator.

If the shut-off valve has a lever, switch, or knob, simply turn it to the closed or off position. This will stop the flow of water to the refrigerator. If the shut-off valve is a twist valve, you will need to twist it clockwise until it stops to shut off the water supply.

Once you have turned off the water supply, it is a good idea to dispense any remaining water in the system. This can be achieved by using the water dispenser on the refrigerator door. Keep a container or towel handy to catch any water that may come out.

By turning off the water supply and emptying the system, you ensure a cleaner and easier process when replacing the water filter.

Step 3: Remove the old water filter

Now that you have turned off the water supply, it’s time to remove the old water filter from your LG refrigerator. Removing the old filter is a straightforward process, but it may vary slightly depending on the model of your refrigerator and the type of filter used.

If your LG refrigerator uses a push-in filter, follow these steps:

1. Locate the release button or tab on the side of the water filter housing.
2. Press the release button or tab firmly to disengage the lock.
3. Gently pull the filter straight out of the housing.

If your LG refrigerator uses a twist-in filter, follow these steps:

1. Hold the filter firmly and twist it counterclockwise until it detaches from the housing.
2. Slowly pull the filter straight out of the housing.

As you remove the old filter, be prepared for some water spillage. It is advisable to have a towel or container ready to catch any water that may come out.

Inspect the removed filter for any signs of damage or clogging. If you notice any issues, it’s a good idea to contact LG customer support for further assistance.

Once you have successfully removed the old water filter, set it aside for proper disposal.

Step 4: Prepare the new water filter

With the old water filter removed, it’s time to prepare the new filter for installation in your LG refrigerator. Properly preparing the new filter ensures optimal performance and a secure fit.

First, check the packaging of the new water filter to ensure it is the correct replacement for your LG refrigerator model. It should match the size and type of the previous filter.

Next, remove the protective cap or cover from the new filter. This cap is typically located on the end of the filter that will be inserted into the water filter housing.

Before inserting the new filter, it is recommended to flush it with water. Flushing helps remove any residual carbon fines or impurities from the manufacturing process. Refer to the instructions provided with the new filter for the specific flushing procedure.

To flush the filter, you might need to run water through it for a certain amount of time or until the water runs clear. This can usually be done by holding the filter under a faucet or submerging it in a container of water.

Once the new filter has been flushed, it is ready to be installed in your LG refrigerator.

Note: If your new water filter has a protective seal or sticker on the end that connects to the water system, make sure to remove it before installation. Leaving the seal or sticker in place can prevent proper water flow and cause filter issues.

To change the water filter in an LG refrigerator, locate the filter housing in the upper right corner of the refrigerator compartment, twist the old filter counterclockwise to remove it, and then insert the new filter and twist it clockwise to secure it in place. Be sure to run water through the dispenser for a few minutes to flush out any air or loose carbon particles.

Step 5: Install the new water filter

Now that you have prepared the new water filter, it’s time to install it in your LG refrigerator. The installation process may vary slightly depending on the model of your refrigerator and the type of filter used, but the following steps will guide you through the general process.

1. Hold the new filter with the end that was flushed facing upwards.
2. If your LG refrigerator uses a push-in filter, align the filter with the housing opening and push it in firmly until it clicks into place.
3. If your LG refrigerator uses a twist-in filter, align the threads on the filter with the housing opening and twist it clockwise until it stops.

Ensure that the new water filter is fully seated and locked into the housing. You should feel it secure and stable. Take a moment to inspect the filter and make sure it is properly aligned.

Make sure that the water filter is installed in the correct orientation, following any arrows or labels on the filter and the filter housing.

Once the new filter is securely installed, give it a gentle tug to ensure it doesn’t come loose. It should stay firmly in place without any movement or wobbling.

Take note of the installation date or mark it on your calendar as a reminder for when the next filter replacement is due.

Congratulations! You have successfully installed the new water filter in your LG refrigerator. Now, it’s time to move on to the final steps.

Step 6: Turn on the water supply

After installing the new water filter in your LG refrigerator, it’s time to turn on the water supply to ensure a steady flow of clean and filtered water. This step is crucial for proper functioning and to avoid any issues with water pressure or flow.

1. Locate the water shut-off valve, which you turned off earlier.
2. Turn the valve counterclockwise or switch it to the open position to allow the water to flow.

With the water supply turned on, you may notice some initial sputtering or spurts of air as the air is purged from the water line. This is normal and should clear up shortly. It’s recommended to let the water flow for a few minutes to ensure any air or trapped particles are flushed out of the system.

While the water is running, check for any leaks around the water filter housing and connections. If you notice any leaks, double-check that the filter is properly seated and tightened. If the leak persists, consult the refrigerator’s user manual or contact LG customer support for further assistance.

Once you have confirmed that there are no leaks and the water flow is steady and uninterrupted, you can proceed to the final step.

Step 7: Reset the filter indicator

After installing the new water filter in your LG refrigerator and turning on the water supply, it’s important to reset the filter indicator. The filter indicator is a handy feature that helps you keep track of when it’s time to replace the filter again.

Depending on your LG refrigerator model, the reset process may vary. Here are some common steps to reset the filter indicator:

1. Locate the filter indicator button or control panel on your LG refrigerator.
2. Press and hold the filter indicator button for a few seconds. The specific duration may vary, so refer to your refrigerator’s user manual for the exact time required.
3. Once the indicator light or display resets or turns off, release the button.

After resetting the filter indicator, it should display a new expiration or replacement date based on the recommended filter lifespan. This ensures that you’ll receive accurate reminders for the next filter replacement.

If you’re unsure about the process or can’t find the filter indicator button, consult your refrigerator’s user manual or contact LG customer support for assistance.

By resetting the filter indicator, you’re ensuring that your LG refrigerator functions optimally and that you’ll have uninterrupted access to clean and filtered water.

Conclusion

Changing the water filter in your LG refrigerator is a simple yet important task to maintain clean and healthy drinking water. By following the steps outlined in this article, you can easily replace the old filter with a new one, ensuring a continuous supply of filtered water in your home.

Remember to locate the water filter, turn off the water supply, remove the old filter, prepare the new filter, install it correctly, turn on the water supply, and finally, reset the filter indicator. These steps are crucial for a successful water filter replacement process.

Regularly changing the water filter in your LG refrigerator helps to remove contaminants, improve the taste of your water and ice, and extend the lifespan of your refrigerator. It is recommended to change the filter every six months or as recommended by the manufacturer.

If you encounter any difficulties during the process or have any questions, consult your refrigerator’s user manual or reach out to LG customer support for assistance. They will be able to provide you with specific instructions tailored to your refrigerator model.

Now that you know how to change the water filter in your LG refrigerator, you can enjoy cleaner and fresher-tasting water whenever you need it. Make it a habit to regularly check and replace the filter to ensure the best performance and maintain the quality of your drinking water.